Delete ESPHome Configuration/esphome-esp360remote.yaml

ESPHome Configuration/esphome-esp360remote.yaml

@@ -1,156 +0,0 @@
-esphome:
-  name: esp360remote
-
-esp32:
-  board: esp32doit-devkit-v1
-  framework:
-    type: arduino
-
-# Enable logging
-logger:
-
-# Enable Home Assistant API
-# Services available for Home Assistant automation and SmartIR
-api:
-  services:
-    - service: send_ir_raw
-      variables:
-        command: int[]
-      then:
-        - remote_transmitter.transmit_raw:
-            transmitter_id: IR_TX
-            code: !lambda 'return command;'
-    - service: send_rf_raw
-      variables:
-        protocol_number: int
-        raw_data: string
-      then:
-        - remote_transmitter.transmit_rc_switch_raw:
-            transmitter_id: RF_TX
-            protocol: !lambda 'return  esphome::remote_base::RC_SWITCH_PROTOCOLS[protocol_number];'
-            code: !lambda 'return raw_data;'
-
-ota:
-  password: ""
-
-wifi:
-  ssid: "nossid"
-  password: "nopassword"
-
-  #HotSpot when it can't connect to WiFi
-  ap:
-    ssid: "Esp360Remote"
-    password: "Esp360Remote"
-
-captive_portal:
-    
-#i2c bus definition
-i2c:
-  sda: 21
-  scl: 22
-  scan: true
-  id: bus_a
-
-#Offsets have been added to the measurements taken. 
-#These are necessary due to the heat generated by the PCB, the second layer of the board, and the case. 
-#This way, sufficiently accurate values are obtained for automations
-sensor:
-  - platform: shtcx
-    temperature:
-      name: "Living Room Temperature"
-      filters:
-        - median: 
-            window_size: 5
-            send_every: 1
-        - offset: -3.7
-    humidity:
-      name: "Living Room Humidity"
-      filters:
-        - median: 
-            window_size: 5
-            send_every: 1
-        - offset: +19.1   
-    address: 0x70
-    update_interval: 300s
-  - platform: bh1750
-    name: "BH1750 Illuminance"
-    filters:
-      - multiply: 5
-    address: 0x23
-    update_interval: 1s
-
-#Setting up IR and RF receivers
-remote_receiver:
-  - id: RF_RX
-    pin: 
-      number: GPIO5
-      inverted: True
-    dump: 
-      - rc_switch
-    tolerance: 35%
-    filter: 200us
-    idle: 4ms
-    buffer_size: 10kb
-    on_rc_switch:
-      - homeassistant.event:
-          event: esphome.rf_code_received
-          data:
-            protocol: !lambda 'return x.protocol;'
-            code: !lambda 'return x.code;' 
-  - id: IR_RX
-    pin: 
-      number: GPIO19
-      inverted: True
-    dump: all
-    on_raw:
-       - homeassistant.event:
-          event: esphome.ir_raw_code_received
-          data:
-            code: !lambda '
-            reverse(x.begin(), x.end());
-            std::string str = "";
-            for (auto it = x.begin(); it != x.end(); ++it)
-            {
-              str += to_string(*it);
-              str += ",";
-              if (it != x.end() - 1) str += " ";
-            }
-            if (str.size() > 0)  str.erase( str.end() - 2);
-            return esphome::to_string("[" + str + "]");'   
-    on_pronto:
-       - homeassistant.event:
-          event: esphome.ir_pronto_code_received
-          data:
-            code: !lambda 'return x.data;'
-    on_lg:
-       - homeassistant.event:
-          event: esphome.ir_lg_code_received
-          data:
-            data: !lambda 'return x.data;'
-            nbits: !lambda 'return x.nbits;'
-    on_panasonic:
-       - homeassistant.event:
-           event: esphome.ir_panasonic_code_received
-           data:
-            address: !lambda 'return x.address;'
-            command: !lambda 'return x.command;'
-
-#Setting up IR and RF transmitters
-remote_transmitter:
-  - id: RF_TX
-    pin: GPIO18
-    carrier_duty_percent: 100%
-  - id: IR_TX
-    pin: GPIO13
-    carrier_duty_percent: 50%
-
-
-web_server:
-  port: 80
-
-#Status LED 
-switch:
-  - platform: gpio
-    pin: 12
-    name: "Status Led"
-    restore_mode: ALWAYS_ON